10-Gigabit fiber optic network interface controller

Product Overview
 AX-X710BM2-F2 is an Ethernet 10-Gigabit dual-port optical network interface controller (NIC) featuring two 10G SFP+ interfaces, supporting a transmission bandwidth of 20Gbps. It also supports PCI-EX8 standard slots, ensuring efficient and stable operation of the NIC. Additionally, the NIC supports VLAN, OOS policies, flow control, and other functions, making it suitable for medium to large-scale local area network applications.

Product Features
·Supports 10Gbps dual fiber channels;
·Interface standard supports PCI Express 3.0;
Supports MSI, MSI-X, and VMDq queues;
·Supports ISCSI acceleration;
·Supports QOS policies;
·Supports FCOE offload;
·Supports RSS/TX queues;
·Supports 802.3x flow control;
·Supports a wide range of network operating systems, allowing for extensive deployment.

Specifications
Product Name: 10-Gigabit Fiber Optic Network Interface Controller
Product model: AX-X710BM2-F2
Processor chip: Intel X710-BM2 10-Gigabit Ethernet controller
Bus type: PCIExpress X8, compatible with PCI-E slots of X8 and X16
Port type: 2 SFP+ interfaces
Barrier height: full-height and half-height configurations
System interface type: PCIe v3.0 (8.0GT/s)
Power consumption: 6.9W
Transmission medium type: LC fiber, compliant with MMF's 62.5/50 micron specifications
Power supply: PCIe power supply
Transmission rate: 10G
Warranty period: Three-year warranty, lifetime maintenance

Technical Specifications
Network standard: IEEE802.3
ISCS1 acceleration: supported
QoS strategy: Support
FCOE offload: supported
RSS/TX Queue: Supported
PXE support: Yes
Interrupt levels: INTA, MSI, MSI-X
Operating temperature: 0°C to 55°C (32°F to 131°F)
Storage temperature: -40°C to 70°C (-40°F to 158°F)
Storage humidity: 35°C 90% non-condensing relative humidity
LED indicator: A flashing green light (Act light) indicates that data is passing through

Installation and connection
To ensure the correct installation of the Ethernet adapter, please follow the steps below
1. Shut down the computer
2. Disconnect the power cable
3. Remove the computer cover and locate the idle PCI-E (X8, X16) bus expansion slot
4. Remove the slot cover plate (if any) by removing the screws or loosening the lever
5. Grip the top edge of the Ethernet adapter and firmly insert it into the card slot
6. Use existing screws or tie bars to re-secure the Ethernet adapter's mounting bracket
7. Close the main unit cover, plug in the cable, and turn on the computer
8. Plug in the optical module and fiber cable

Fault handling methods
1. The Link indicator light does not illuminate after the optical module is inserted
★ Is the server turned on?
★ Is the Ethernet adapter properly inserted into the PCI-E bus expansion slot?
★If it still cannot be used normally, it may be due to dirt, sweat stains, or other contaminants on the gold fingers of the card, causing poor contact between the card and the motherboard slot. Cleaning the gold fingers with a rubber eraser usually resolves the issue and allows normal use;
★Whether the optical module is inserted correctly, only when it is inserted correctly, the Link indicator light will be lit;
★ If the issue remains unresolved, please contact the after-sales service department for assistance;
2. The ACT indicator light does not flash after the fiber optic cable is connected
★ Check if the TX and RX interfaces of the fiber optic cable are properly connected?
★Check if the optical module is matched?
★ Check whether the fiber cable matches the optical module (multi-mode or single-mode)?
If you encounter any issues with the product and need assistance, please contact our after-sales service department for resolution;

Precautions for use
★Pay attention to anti-static protection during product installation.
★ Do not place this product in a damp environment, such as a bathroom
★ Prevent damage from corrosive substances, such as hydrochloric acid, sulfuric acid, caustic soda, oxalic acid, etc
★ Please refrain from unauthorized modification, disassembly, or repair.
★ Do not bake at high temperatures, as the casing and electronic components of the device may be damaged.
★Please avoid exposing this product to direct sunlight, as the casing and electronic components may be damaged.
★ Prevent impact, as external impact may damage the product.
★ Operating temperature: -40°C to 70°C; operating humidity: 35% to 90% non-condensing relative humidity.

Our Advantages
Excellent technical skills and rich experience
Independent research and development, craftsmanship and intelligence, customizable needs
Imported chips, high-quality solutions, stable performance
Fully compatible. Senior talents to solve technical problems
DDM digital diagnosis real-time monitoring module status
Special test: All performance items have been tested and meet the required standards